**The new Raspberry Pi bootloader is out which makes these instructions only necessary if you want to continue to use the SD card as a bootloader. View the Raspberry Pi Bootloader Configuration Guide here!**
The Raspberry Pi 4* is finally here and has a lot of exciting changes. One very major downside is that it doesn’t support true USB booting yet out of the box (like the 3 series did). The Raspberry Pi foundation states that it is being worked on and will be added back with a future update. No timeline has been given yet for that to happen but they state it’s one of their top priorities.
Most of my projects heavily depend on having good performing storage so sitting and waiting was not an acceptable solution. In this guide I’ll show you a workaround to use USB devices as your rootfs device and use a Micro SD card as bootloader only which gives us full SSD performance after boot! To see exactly how much of a performance difference this makes (spoiler: it’s gigantic) check out the Raspberry Pi Storage Benchmarks.
I highly recommend doing this on a completely new install. If you try to upgrade your old ones and something goes wrong there’s a good chance you might lose data. We will be modifying the boot partition, resizing partitions, etc. so don’t use a drive with any data on it unless you are positive you have all of the steps down!
Compatible USB Adapters
The Raspberry Pi 4 is proving to be picky about what SATA, M.2, etc. adapters will work in the USB 3.0 port. The USB 3.0 ports are the ones in the middle that are blue inside. The black ones are USB 2.0 and won’t give you the faster speeds the new Pi offers.
It’s very likely that some of these will be fixed via software and firmware updates and the Raspberry Pi Foundation has several open known issues related to USB 3. Until that happens though I will maintain a list here of known working ones and known problematic ones. It’s still very early in the release of the Pi 4 so we still have a lot to learn about which adapters work / don’t work. If you have working and nonworking adapters leave a comment and I’ll add it in this list.
If the adapters worked before on older Pis then one thing you can try is putting them in the black USB 2.0 ports. Obviously this is stupid because we all want the Pi 4 performance gains but if you end up needing to buy a new adapter this will give you a workaround until a replacement arrives!
Find USB adapter chipset
There are certain chipsets used in adapters that are known to be working/not working.
pi@raspberrypi:~ $ lsusb Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 002: ID 174c:55aa ASMedia Technology Inc. Name: ASM1051E SATA 6Gb/s bridge, ASM1053E SATA 6Gb/s bridge, ASM1153 SATA 3Gb/s bridge, ASM1153E SATA 6Gb/s bridge Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 2109:3431 VIA Labs, Inc. Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
This is a lsusb dump of all my connected USB devices. I have bolded the line with the USB bridge device. We can see that the chipset is ASM1153E. This is a really common one that works well with the Pi.
The new USB-C 3.1 Type A version of the Sabrent adapter is reported as working in the comments by UEF. DO NOT get the USB 3.0 version as that one is below on the naughty list and won’t work!
Make absolutely sure it’s the 10Gbps USB 3.1 Gen 2 version. There is another one that looks identical that is a USB 3.1 Gen 2 6Gbps that will not work. Confirmed working by RRT in the comments.
It’s bold. It’s beautiful. It’s also confirmed working by TADRACKET and Steve B. However, be warned, it takes a *lot* of power! Steve B. reports that even with the oversized 3.5A CanaKit adapter* it does not work. If you have the standard 3.0 adapter you can be practically certain it won’t power this enclosure. Does work with a powered USB hub*.
Returning legendary commentary Frank Meyer reports: Does not work with a 3.0A power adapter (also reported by TTE). It’s not enough power for this enclosure. Does work with a powered USB hub*.
M.Yusuf has given the first ever report of a working Orico adapter! Make sure it’s the USB 3.1 Gen 2 version that says “Support UASP for NVMe SSD”. This is the way.
Canakit has been making very reliable power supplies for several Pi generations now. Using a 3.5A power supply will give enough extra power for your Pi to power the drive without causing instability
Reported as working by JeffG but with an ugly messy appearance
Known Working Adapters
Known Problematic Adapters (Naughty List)
Here is a list of common USB adapters that are known to have problems with the Raspberry Pi 4. You can get some of these adapters working by using quirks mode (see the “Fix (some) USB Adapter Problems Using Quirks” section below).
Only works in the USB 2.0 ports. Will not boot in a USB 3.0 port. I have two of these and can confirm they don’t work. RIP to Sabrent, our previous king of the Pi 3 era of adapters.
Despite earlier reports as working Ryan and one other have reported this adapter does not work unless you enable quirks mode! Don’t make Ryan’s sacrifice in vain and avoid this one.
Extremely cheap adapter from AliExpress — MADATALIEXPRESS bought 5 of them and none worked, PPCM had one working, very unreliable and slow when it does work, not recommended even if you get lucky!
The Samsung 980 Pro (NVMe) is a professional grade SSD and one of the fastest in the world. The Samsung NVMe drives have been at the top of this category for a long time and are well trusted for both their performance and reliability / long life.
The ICY BOX is basically a giant heatsink that you mount a high performance M.2 NVMe drive inside of. This enclosure is really fast but requires a powered USB hub. Not even the 3.5A adapter can reliably power it! The enclosure works well and will physically feel warm to the touch as it is pulling the heat off your NVMe drive!
The Kingston A400 has been a great drive to use with the Pi for years. It’s reliable, widely available around the world, has low power requirements and performs very well. It’s also very affordable. This drive has been benchmarked over 1000 times at pibenchmarks.com and is the #1 most popular SSD among the Pi community!
The SanDisk Extreme Pro USB SSD is a true solid state drive. This is different than a typical “flash drive” which uses extremely cheap memory and has very low random I/O performance/throughput compared to a real solid state drive. I’ve used both the USB 3.1 and USB 3.2 variants with the Pi successfully and they benchmark very well!
You may use other types of drives with the Pi such as M.2 SATA to USB 3.0 and m-SATA to USB 3.0. Here’s some adapters I’ve used for those types of drives:
VL716 mSATA Enclosure
The VL716 mSATA enclosure lets you connect micro SATA drives to the Pi. These drives are an older type of SSD (usually seen in laptops) predating the M.2 slot but are still widely available and perform extremely well!
The UGREEN M+B enclosure is a great enclosure for the Pi for M.2 SATA 2280 NGFF drives. It supports both B-key and M-key drives. Does not support newer NVMe drives. As with other types of enclosures it requires more power than other options!
The Argon ONE M.2 is a M.2 SATA Pi 4 case / storage solution. With the case and M.2 SATA expansion board you can completely enclosure your Pi 4 and have a built in M.2 slot! The M.2 SATA board is sometimes sold separately from the case itself and can be used as well. Does not support NVMe, this is for SATA M.2 drives only!
Power can be a serious problem with these drives. We are learning from the comments that you are especially likely to run into power issues with NVMe enclosures. A powered USB hub or a power adapter that puts out 3.5A comes not only just strongly recommended, it may actually be required that you choose one option or the other for your drive to function.
The specific requirements of how much power you’ll need depend on the adapter/enclosure and the model of your drive itself. As a very rough guideline, older models of drives tend to use more power than newer models of drives. 3.5″ form factor drives also use more power than 2.5″ drives. The earliest SSD models like first and second generation models are also well understood to use significantly more power than newer models. This is due to changes and improvements in technology over the years and even using different more efficient memory like 3D NAND. Some super high end performance drives will consume more power as well.
Here’s the current recommendations based on everyone’s comments combined with stuff I’ve personally used with the Pi:
CanaKit 3.5A Power Adapter
The CanaKit 3.5A adapter has an extra half an amp (500 mA) of capacity to give some breathing room to your accessories. This is bigger than the official Pi power supply which provides 3.0A.
The Sabrent powered USB hub delivers a whopping 2.5A of dedicated power for your USB attached devices. This is almost as much as the Pi adapter itself is rated for (3.0A). It will easily power the most thirsty of setups such as NVMe enclosures.
Note: Make sure Amazon doesn’t try to take you to the non-powered version and that it’s the one with the AC adapter that plugs in to provide extra power
Fixing (some) USB Adapter Problems Using Quirks
Some of the very common adapters on the naughty list above (such as the Sabrent) can be made to work by using USB quirks to disable UAS mode on the drive. This lowers performance, but it’s still much faster than a SD card and your adapter won’t go to waste.
To find out the quirks we need to find the device ID string for your adapter and then add an entry to cmdline.txt telling the kernel to apply them on boot.
Find Your Adapter
To apply the quirks we first need to get the adapter id. We will use the sudo lsusb command:
$ sudo lsusb
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 002: ID 174c:55aa ASMedia Technology Inc. Name: ASM1051E SATA 6Gb/s bridge, ASM1053E SATA 6Gb/s bridge, ASM1153 SATA 3Gb/s bridge, ASM1153E SATA 6Gb/s bridge
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 2109:3431 VIA Labs, Inc. Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
On line 2 we can see my ASM1051E SATA 6Gb/s bridge adapter (it’s the known working StarTech.com 2.5″ SATA to USB adapter*). You will see something very similar to mine when you run the command and it shouldn’t be too hard to figure out which device it is. If you need more information add a -v switch to make the command sudo lsusb -v. This can sometimes add some additional details to make it easier to figure out which one is your adapter.
If you’re still not sure, we have another command that between the two that can narrow things down. Type / paste the following:
sudo dmesg | grep usb
[ 0.828535] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.828568] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.828597] usb usb3: Product: DWC OTG Controller
[ 0.828620] usb usb3: Manufacturer: Linux 4.19.75-v7l+ dwc_otg_hcd
[ 0.828644] usb usb3: SerialNumber: fe980000.usb
[ 0.830051] usbcore: registered new interface driver uas
[ 0.830182] usbcore: registered new interface driver usb-storage
[ 0.836488] usbcore: registered new interface driver usbhid
[ 0.836511] usbhid: USB HID core driver
[ 0.971598] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[ 1.154217] usb 1-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.20
[ 1.154254] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.154281] usb 1-1: Product: USB2.0 Hub
[ 1.301989] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 1.332965] usb 2-1: New USB device found, idVendor=174c, idProduct=55aa, bcdDevice= 1.00
[ 1.332999] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 1.333026] usb 2-1: Product: ASM105x
[ 1.333048] usb 2-1: Manufacturer: ASMT
[ 1.333071] usb 2-1: SerialNumber: 123456789B79F
This is the dmesg log showing the hardware detection as hardware is activated on the Pi. If your log is really long you can generate fresh entries by just unplugging a device and plugging it back in and running the command again. Here we can clearly see that the ASM105x is what our StarTech adapter is being detected as.
Now we can go back to our first lsusb command and we want the 8 characters from the ID field that comes right after the Device:
Bus 002 Device 002: ID 174c:55aa ASMedia Technology Inc. Name: ASM1051E SATA 6Gb/s bridge
Our adapter’s ID is: 174c:55aa
Applying Quirks
To apply the quirks to our USB adapter we are going to edit /boot/cmdline.txt. Type:
sudo nano /boot/cmdline.txt
We are going to add the following entry into the very front of cmdline.txt:
usb-storage.quirks=XXXX:XXXX:u
In place of the X’s above you will put in your adapter’s ID that we got before. With the example commands I gave above mine would look like this: usb-storage.quirks=174c:55aa:u. After this my cmdline.txt looks like this (everything should be one continuous line, no line breaks!):
Now reboot the Pi. If the Pi fails to boot you can plug the SD card into the computer and go to /boot/cmdline.txt and undo the change we did so you can boot back in with your SD card.
Verifying Quirks
Once you have rebooted after changing cmdline.txt we can verify the quirks have been applied by doing another dmesg | grep usb command:
sudo dmesg | grep usb
[ 1.332924] usb 2-1: New USB device found, idVendor=174c, idProduct=55aa, bcdDevice= 1.00
[ 1.332957] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 1.332983] usb 2-1: Product: ASM105x
[ 1.333006] usb 2-1: Manufacturer: ASMT
[ 1.333028] usb 2-1: SerialNumber: 123456789B79F
[ 1.335967] usb 2-1: UAS is blacklisted for this device, using usb-storage instead
[ 1.336071] usb 2-1: UAS is blacklisted for this device, using usb-storage instead
[ 1.336103] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 1.336479] usb-storage 2-1:1.0: Quirks match for vid 174c pid 55aa: c00000
[ 1.336611] scsi host0: usb-storage 2-1:1.0
This time we can see in dmesg that UAS was blacklisted for the device and it has loaded with the usb-storage driver instead. This driver tends to be more compatible with the “problematic adapters” but the performance is usually significantly lower. It’s definitely worth a try though as some adapters do better with the quirks performance-wise. The only way to know for sure is to run a benchmark (see storage benchmark section near the end).
USB Boot Instructions
There are a lot of steps to follow to set everything up properly. If you make a mistake the first time don’t spend too much time trying to correct it or figure out what you did wrong. It’s usually faster to burn the images again and reconfigure again rather than try to figure out which step you might have made a typo on. It’s much easier the second time!
Note: Don’t attempt to use raw dd commands to write the images. Too many silly things can go wrong that are checked for/fixed by the recommended programs. Do yourself a big favor and use one of the recommends to avoid spending a ton of time troubleshooting basic imaging problems!
Preparing SSD
We are going to burn a second identical copy of Raspbian to the SSD. This ensures everything the Pi needs to boot is there so we can use the SD card as a bootloader but our actual system will be on our nice fast SSD drive.
Note: Make sure you create the empty file named “ssh” on the boot partition of both drives if you are headless or don’t have a mouse/keyboard attached so you can ssh in on the first boot.
First Boot (SD card only, SSD unplugged)
Insert your freshly imaged SD card into the Pi and connect the power. Sign into the Pi for the first time.
Don’t do an apt-get upgrade/dist-upgrade or any additional configuration yet. Just stick with the instructions until we have finished configuration (especially since if something goes wrong you may have to start over and any other setup you did will be lost).
Once the Pi has finished booting and you have signed in for the first time plug in your SSD to your Pi’s USB 3.0 ports. The USB 3.0 ports are the ones that have the blue plastic inside instead of the black plastic (the black ones are USB 2.0 ports).
Change PARTUUID
We need to change the PARTUUID of our SSD’s partitions so the Pi doesn’t get confused about what device to boot from. Right now the partitions on both the SD card and the SSD are an exact match and we need them to be different so we can tell the Pi to boot specifically from our SSD’s partition.
We are going to use fdisk to change the SSD’s PARTUUID to the hexadecimal d34db33f to make our SSD easy to identify. Use the following:
$ sudo fdisk /dev/sda
Welcome to fdisk (util-linux 2.33.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Command (m for help): p
Disk /dev/sda: 238.5 GiB, 256060514304 bytes, 500118192 sectors
Disk model: ASM105x
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x6c586e13
Device Boot Start End Sectors Size Id Type
/dev/sda1 8192 532479 524288 256M c W95 FAT32 (LBA)
/dev/sda2 532480 500118191 499585712 238.2G 83 Linux
Command (m for help): x
Expert command (m for help): i
Enter the new disk identifier: 0xd34db33f
Disk identifier changed from 0x6c586e13 to 0xd34db33f.
Expert command (m for help): r
Command (m for help): w
The partition table has been altered.
Syncing disks.
Your /dev/mmcblk0 and /dev/sda devices should now be different from each other. The SD card’s ID is 6c586e13 and the SSD’s PARTUUID is now
Update /boot/cmdline.txt
We are going to change cmdline.txt to point to the SSD for booting instead of the SD card. First make a backup of your existing cmdline.txt file with the following command:
sudo cp /boot/cmdline.txt /boot/cmdline.txt.bak
We’ve now created a backup you can restore if something goes wrong. If you need to restore your backup plug the SD card into a computer/device and replace cmdline.txt with cmdline.txt.bak that we made above. Now your Pi should boot normally again.
Open up /boot/cmdline.txt using nano or your favorite text editor:
Make the change and double check the line is what it should be,then press Ctrl+X to save our changes.
Note: cmdline.txt should be one long solid line with no breaks — don’t add any line breaks or the system won’t boot and you’ll need to restore the backup we made earlier!
Test SSD
We are now ready to test booting from the SSD. Restart your Pi by issuing a
sudo reboot
The first boot with your SSD can be slow due to running fsck on the drive. If you have a really large SSD it can take surprisingly long to check all that space. Once the check completes it will mark the drive clean and skip the disk check from now on. It can take over a minute or two sometimes for really big drives so give it at least that much time before assuming it didn’t work.
After signing in we can verify that the SSD is being used like this:
$ findmnt -n -o SOURCE /
/dev/sda2
Verify that partition has switched over as shown below to /dev/sda2 (SSD) instead of /dev/mmcblk0p2 (SD card).
Update /etc/fstab
We are now ready to edit the /etc/fstab file to point to our updated drive. To edit the file type:
We want to change the root ( / ) partition (PARTUUID ending with -02) to load our SSD’s PARTUUID instead of the SD card. Replace the 2nd partition’s PARTUUID field on the last line in the file with the d34db33f label we applied earlier with fdisk. After making the change my /etc/fstab file looks like this:
Press Ctrl+X to tell nano to save our changes. Now type sudo reboot to restart the Pi.
Note: We want to leave the first partition (/boot) on the SD card. If you change this to the SSD then apt will update your SSD instead of the SD card so they won’t be used during boot! Remember that we are using the SD card as a bootloader and that is why the firmware updates (such as start.elf, etc) should go there instead of the SSD’s boot partition (which is never used).
Resizing Filesystem
By default the partition on the SSD / Flash drive will only be 1.8G. The Pi expands this automatically on micro SD drives but we will need to do it ourselves for a SSD / Flash drive. To do this we need to expand the partition and then resize the file system.
First let’s open fdisk and print the partitions:
pi@raspberrypi:~ $ sudo fdisk /dev/sda
Welcome to fdisk (util-linux 2.33.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Command (m for help): p
Disk /dev/sda: 238.5 GiB, 256060514304 bytes, 500118192 sectors
Disk model: ASM105x
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xd34db33f
Device Boot Start End Sectors Size Id Type
/dev/sda1 8192 532479 524288 256M c W95 FAT32 (LBA)
/dev/sda2 532480 4390911 3858432 1.9G 83 Linux
There is the line we need. Our start value for /dev/sda2 (rootfs) is 532480. Next we need to remove and recreate the partition as a larger size.
If you make any mistakes during this command just close fdisk by pressing q. The changes won’t be written to disk. If you mess up any of the commands the drive will no longer boot and you’ll have to start over again so be careful!
Command (m for help): d
Partition number (1,2, default 2): 2
Partition 2 has been deleted.
Command (m for help): n
Partition type
p primary (1 primary, 0 extended, 3 free)
e extended (container for logical partitions)
Select (default p): p
Partition number (2-4, default 2): 2
First sector (2048-500118191, default 2048): 532480
Last sector, +/-sectors or +/-size{K,M,G,T,P} (532480-500118191, default 500118191): 500118191
Created a new partition 2 of type 'Linux' and of size 238.2 GiB.
Partition #2 contains a ext4 signature.
Do you want to remove the signature? [Y]es/[N]o: N
Command (m for help): w
The partition table has been altered.
Syncing disks.
If everything went well then type “w” and press enter. Otherwise press “q” to quit and try again. Once you enter “w” the changes will be permanently written to disk!
Now reboot the system. Type “df -h” to view the current disk:
We can see our disk is still 1.8G even after resizing the partition. That’s because we still have one more step! We need to resize the filesystem to fill our new partition space. For this we will use “sudo resize2fs /dev/sda2”:
sudo resize2fs /dev/sda2
resize2fs 1.44.5 (15-Dec-2018)
Filesystem at /dev/sda2 is mounted on /; on-line resizing required
old_desc_blocks = 1, new_desc_blocks = 15
The filesystem on /dev/sda2 is now 62448214 (4k) blocks long.
And that’s it! You will now be using all of your space on your drive.
Verify SSD Functionality / Performance
You can make sure everything is running correctly (and as fast as it should be) by running my quick storage benchmark. You can run the benchmark with the following one-liner:
This will give you a score you can compare to the other Raspberry Pi Storage Benchmark results and make sure that you are getting an equivalent speed to your peers with the same device!
Update Pi using apt
Now that we’ve updated fstab it is safe (and highly recommended) to update your Pi’s software. Type “sudo apt-get update && sudo apt-get dist-upgrade” to update the system and firmware.
Your system will now be running completely from your USB drive! To verify this, run the command “findmnt -n -o SOURCE” / to ensure your root partition has switched over as shown below to /dev/sda2 instead of /dev/mmcblk0p2.
Conclusion
The Samsung 950 Pro NVMe drive in the featured picture scored a 9189 on the Raspberry Pi Storage Benchmark. The previous all-time record score on a Pi 3B+ was 3561. The performance gains are very real and very dramatic.
For me getting this performance is well worth having to waste a micro SD card just to be a bootloader. I am largely after the USB 3.0 bus and gigabit ethernet performance improvements and using this method I am able to achieve the performance I was after without waiting an indeterminate amount of time for the feature to be added back in!
Although there are ongoing compatibility issues and we lack the super easy native USB booting support we had before I’m more than willing to go through the growing pains to finally get rid that ancient USB 2.0 bus! Just make sure if you are planning to build a system you plan your adapters and parts accordingly.
I plan to set up a Minecraft Server for me and my friends on a Rasp 4 with 4gb Ram, and I wonder if a external power supply for the SSD would make a difference.
I’m talking about products like this one
With past Pis it generally has been okay to power it using the Pi’s onboard USB ports
However on the Pi 4 (even though it has more power) it could definitely be more stable to power the hard drive externally like with this adapter.
The only question then will be compatibility. If you try it and it works let us know!
tl;dr: It can’t hurt to have external power for any USB devices, but I’ve had better luck with the Pi4 power and no external USB power.
Longer: I’ve had absolutely no problem powering two SSD drives from the Pi4 using the Pi-branded USBC power supply. With a Pi3 using the same SATA/USB adapter I’m using with the Pi4 I would get low-power resets when powering the system from a 2A USB-A power supply.
The Raspberry Pi 4 does not have this boot mode support like the 3 series yet featured in the link. The Raspberry Pi foundation is working on adding this back in but for the moment you need to do a workaround like my article to get a USB rootfs.
It might be worth nothing that on first reboot onto the SSD there will be a loooong period of LED blinking with not viable network. This seems to be normal and not a “oh no, things aren’t working” situation. It might also be worth mentioning that this whole thing is needed due to the “boot from USB” instructions for Pi3 no longer working, AND that creating the “ssh” file onto /boot of the SSD drive will be necessary even if you’ve already been using SSH into a headless Pi4 booting from the memory card.
Thanks for the instructions! While this has still been a pain, you’ve saved me lots of time.
Update: The adapter I mention above seems to suffer from really bad I/O performance. Avoid it, at least for now (I haven’t determined if it ALSO has bad I/O performance when it’s just a USB device hanging off a Pi4 running from the card). This one [ StarTech 2.5″ SATA to USB Adapter ] appears to be working though.
# lsusb | grep SATA
Bus 002 Device 002: ID 174c:55aa ASMedia Technology Inc. Name: ASM1051E SATA 6Gb/s bridge, ASM1053E SATA 6Gb/s bridge, ASM1153 SATA 3Gb/s bridge, ASM1153E SATA 6Gb/s bridge
# dd if=/dev/zero of=/root/test bs=8k count=500k conv=fsync
512000+0 records in
512000+0 records out
4194304000 bytes (4.2 GB, 3.9 GiB) copied, 18 s, 233 MB/s
Looks like it’s the same chipset/device that Krikkit is reporting success with, though packaged up by a different vendor. I seem to be getting even better I/O than Krikkit is, too. Neat!
More followup:
Using the JMicron adapter (above, with the extremely bad I/O performance when plugged into the USB3 ports) can produce reasonable results if you plug it into an intermediary USB3 hub. I’ve plugged it into this one and am now seeing:
# sudo dd if=/dev/zero of=/mnt/sdb_btrfs/test bs=8k count=500k conv=fsync
512000+0 records in
512000+0 records out
4194304000 bytes (4.2 GB, 3.9 GiB) copied, 21.6255 s, 194 MB/s
For comparison here’s another drive (the /root drive, a PNY 120GB SSD) using the ASM1051E chipset (the “StarTech” mentioned above) connected directly to the USB3 bus (NOT going through an intermediary hub):
# sudo dd if=/dev/zero of=/mnt/test bs=8k count=500k conv=fsync
512000+0 records in
512000+0 records out
4194304000 bytes (4.2 GB, 3.9 GiB) copied, 16.5049 s, 254 MB/s
The difference in performance could be due to the USB hub not being great, or the JMicron already known to be janky, or the 60GB SSD in it not being new and fancy like the PNY. Hard to say. Still, the 194MB/s is certainly better than the ~30MB/s it was hitting on the USB2 interface, and WAY better than the I/O Timeout errors it was sporadically throwing from the USB3 interface.
Thanks for the feedback, I’m glad it was able to help save time! I’ve added your suggestions in the article in new/updated sections to hopefully save others even more time going forward!
Additional learnings after a bit of goofing around:
* The JMicron adapter still works as expected on the USB2 bus. It’s just really sad. ~30MB/s vs ~231MB/s for the ASMedia adapter on the USB3 bus.
* The USB3 + SSD combination has MUCH better I/O performance than my SanDisk micro-SD card.
* Seems as though there’s no good way to get btrfs running on the partition that holds the kernel and modules. I’ll need to do decide if I care enough about getting the whole (mostly) system onto btrfs, or am OK with the OS parts of the filesystem on the default ext4 and just remap the data I care about (databases, /etc, etc) remapped into paths in a btrfs hierarchy
* Haven’t yet done a power comparison versus the Pi3 for my work loads. The Pi3 was pulling ~4 watts for my workload and was much, much slower. I’m curious to see if the Pi4 with the same workload (though updated to Buster, with 2GB RAM, quad-core and faster CPU) stays within the same budget of <10 watts.
* Migrating from the Pi3 to the Pi4 has reminded me, again, what a pain it is to backup/restore Linux in general. Dependency hell, configurations and data scattered across many many directories, incompatible configuration changes from one version of a distro to another, etc. Keep good notes! You'll need them again in the future. 🙂
All-in-all the Pi4 is an amazing upgrade from the Pi3. You never really think of how constraining the Pi3 is until you get a to do the same work on a more robust system (as opposed to doing a lot of work on an EC2 instance where you expect the performance to be different and thus don't really compare it to the micro-work you're doing on the Pi). Just looking forward to the improvements in USB3 support as they move forward (native USB and/or network booting would be fantastic).
root@raspi4:~# lsusb
Bus 002 Device 002: ID 174c:55aa ASMedia Technology Inc. Name: ASM1051E SATA 6Gb/s bridge, ASM1053E SATA 6Gb/s bridge, ASM1153 SATA 3Gb/s bridge, ASM1153E SATA 6Gb/s bridge
AND it is WORKING!!! …quick test with dd showed the following stats:
root@raspi4:~# sudo dd if=/dev/zero of=/root/test bs=8k count=500k conv=fsync
512000+0 records in
512000+0 records out
4194304000 bytes (4.2 GB, 3.9 GiB) copied, 25.3591 s, 165 MB/s
Thanks for the tuto. FWIW the Inatek fe2008 mSATA USB 3 adapter works fine for me, I found it easily on Amazon.
I plan to set up a Minecraft Server for me and my friends on a Rasp 4 with 4gb Ram, and I wonder if a external power supply for the SSD would make a difference.
I’m talking about products like this one
What are your thoughts on this?
With past Pis it generally has been okay to power it using the Pi’s onboard USB ports
However on the Pi 4 (even though it has more power) it could definitely be more stable to power the hard drive externally like with this adapter.
The only question then will be compatibility. If you try it and it works let us know!
tl;dr: It can’t hurt to have external power for any USB devices, but I’ve had better luck with the Pi4 power and no external USB power.
Longer: I’ve had absolutely no problem powering two SSD drives from the Pi4 using the Pi-branded USBC power supply. With a Pi3 using the same SATA/USB adapter I’m using with the Pi4 I would get low-power resets when powering the system from a 2A USB-A power supply.
modifying the boot/config.txt file won’t work ?
Hey sozen,
The Raspberry Pi 4 does not have this boot mode support like the 3 series yet featured in the link. The Raspberry Pi foundation is working on adding this back in but for the moment you need to do a workaround like my article to get a USB rootfs.
Note:
Don’t forget to edit /etc/fstab with the correct information!!!
Awesome!. a million thanks, the first post that runs the usb boot.
This adapter appears to be working(Updated: read reply).It might be worth nothing that on first reboot onto the SSD there will be a loooong period of LED blinking with not viable network. This seems to be normal and not a “oh no, things aren’t working” situation. It might also be worth mentioning that this whole thing is needed due to the “boot from USB” instructions for Pi3 no longer working, AND that creating the “ssh” file onto /boot of the SSD drive will be necessary even if you’ve already been using SSH into a headless Pi4 booting from the memory card.
Thanks for the instructions! While this has still been a pain, you’ve saved me lots of time.
Update: The adapter I mention above seems to suffer from really bad I/O performance. Avoid it, at least for now (I haven’t determined if it ALSO has bad I/O performance when it’s just a USB device hanging off a Pi4 running from the card). This one [ StarTech 2.5″ SATA to USB Adapter ] appears to be working though.
# lsusb | grep SATABus 002 Device 002: ID 174c:55aa ASMedia Technology Inc. Name: ASM1051E SATA 6Gb/s bridge, ASM1053E SATA 6Gb/s bridge, ASM1153 SATA 3Gb/s bridge, ASM1153E SATA 6Gb/s bridge
# dd if=/dev/zero of=/root/test bs=8k count=500k conv=fsync
512000+0 records in
512000+0 records out
4194304000 bytes (4.2 GB, 3.9 GiB) copied, 18 s, 233 MB/s
Looks like it’s the same chipset/device that Krikkit is reporting success with, though packaged up by a different vendor. I seem to be getting even better I/O than Krikkit is, too. Neat!
Further update: The adapter mentioned in my original response is evidently a JMicron chipset:
# lsusb | grep JMicron
Bus 002 Device 003: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge
I’ve confirmed that the I/O for this adapter is just abysmal on the PI4 USB3 bus. Haven’t tried it on the USB2 bus yet.
More followup:
Using the JMicron adapter (above, with the extremely bad I/O performance when plugged into the USB3 ports) can produce reasonable results if you plug it into an intermediary USB3 hub. I’ve plugged it into this one and am now seeing:
# sudo dd if=/dev/zero of=/mnt/sdb_btrfs/test bs=8k count=500k conv=fsync512000+0 records in
512000+0 records out
4194304000 bytes (4.2 GB, 3.9 GiB) copied, 21.6255 s, 194 MB/s
For comparison here’s another drive (the /root drive, a PNY 120GB SSD) using the ASM1051E chipset (the “StarTech” mentioned above) connected directly to the USB3 bus (NOT going through an intermediary hub):
# sudo dd if=/dev/zero of=/mnt/test bs=8k count=500k conv=fsync512000+0 records in
512000+0 records out
4194304000 bytes (4.2 GB, 3.9 GiB) copied, 16.5049 s, 254 MB/s
The difference in performance could be due to the USB hub not being great, or the JMicron already known to be janky, or the 60GB SSD in it not being new and fancy like the PNY. Hard to say. Still, the 194MB/s is certainly better than the ~30MB/s it was hitting on the USB2 interface, and WAY better than the I/O Timeout errors it was sporadically throwing from the USB3 interface.
Hey dzm,
Thanks for the feedback, I’m glad it was able to help save time! I’ve added your suggestions in the article in new/updated sections to hopefully save others even more time going forward!
Additional learnings after a bit of goofing around:
* The JMicron adapter still works as expected on the USB2 bus. It’s just really sad. ~30MB/s vs ~231MB/s for the ASMedia adapter on the USB3 bus.
* The USB3 + SSD combination has MUCH better I/O performance than my SanDisk micro-SD card.
* Seems as though there’s no good way to get btrfs running on the partition that holds the kernel and modules. I’ll need to do decide if I care enough about getting the whole (mostly) system onto btrfs, or am OK with the OS parts of the filesystem on the default ext4 and just remap the data I care about (databases, /etc, etc) remapped into paths in a btrfs hierarchy
* Haven’t yet done a power comparison versus the Pi3 for my work loads. The Pi3 was pulling ~4 watts for my workload and was much, much slower. I’m curious to see if the Pi4 with the same workload (though updated to Buster, with 2GB RAM, quad-core and faster CPU) stays within the same budget of <10 watts.
* Migrating from the Pi3 to the Pi4 has reminded me, again, what a pain it is to backup/restore Linux in general. Dependency hell, configurations and data scattered across many many directories, incompatible configuration changes from one version of a distro to another, etc. Keep good notes! You'll need them again in the future. 🙂
All-in-all the Pi4 is an amazing upgrade from the Pi3. You never really think of how constraining the Pi3 is until you get a to do the same work on a more robust system (as opposed to doing a lot of work on an EC2 instance where you expect the performance to be different and thus don't really compare it to the micro-work you're doing on the Pi). Just looking forward to the improvements in USB3 support as they move forward (native USB and/or network booting would be fantastic).
Sabrent USB 3.0 to 2.5″ SATA adapter does not work with my raspi 4 4 gb, sorry i have 2 of them 🙁
…just tried my other adapter:
CSL SL – USB 3.0 auf SATA Adapter
root@raspi4:~# lsusbBus 002 Device 002: ID 174c:55aa ASMedia Technology Inc. Name: ASM1051E SATA 6Gb/s bridge, ASM1053E SATA 6Gb/s bridge, ASM1153 SATA 3Gb/s bridge, ASM1153E SATA 6Gb/s bridge
AND it is WORKING!!! …quick test with dd showed the following stats:
root@raspi4:~# sudo dd if=/dev/zero of=/root/test bs=8k count=500k conv=fsync512000+0 records in
512000+0 records out
4194304000 bytes (4.2 GB, 3.9 GiB) copied, 25.3591 s, 165 MB/s
Those are beautiful numbers! Thanks for letting us know, I’ll add it to the list of working adapters!